Brake booster vacuum switch (F190): Difference between revisions

From Golf Ecomatic
Jump to navigation Jump to search
Created page with "The brake booster vacuum switch (F190) informs the DIGISWING control unit whether the pressure in the brake system is satisfactory. Type: open/closed Colour: Red Switch clos..."
 
No edit summary
Line 1: Line 1:
The brake booster vacuum switch (F190) informs the DIGISWING control unit whether the pressure in the brake system is satisfactory.
The brake booster vacuum switch (F190) informs the [[Digiswing]] control unit whether the pressure in the brake system is satisfactory.


Type: open/closed
Type: open/closed
Line 8: Line 8:


If the switch closes (vacuum pressure too low), the engine is off, and the vehicle is moving, the engine is immediately restarted to restore vacuum to the brake circuit via the mechanical exhauster.
If the switch closes (vacuum pressure too low), the engine is off, and the vehicle is moving, the engine is immediately restarted to restore vacuum to the brake circuit via the mechanical exhauster.
If this switch is closed, the priority shift valve is closed and the clutch and brake circuits are separated, the engine will not switch off.
If this switch is closed, the priority shift valve is closed and the clutch and brake circuits are separated, the engine will not switch off.


Line 14: Line 15:
== Test procedure without diagnostic equipment ==
== Test procedure without diagnostic equipment ==


-Start engine and leave ecomatic mode on
*Start engine and leave Ecomatic mode on
-Find a downhill gradient or open stretch of road which is safe to carry out the procedure below.
*Find a downhill gradient or open stretch of road which is safe to carry out the procedure below.
-Allow vehicle to start rolling down the gradient with engine off
*Allow vehicle to start rolling down the gradient with engine off
-Keep pressing brake pedal on and off.
*Keep pressing brake pedal on and off.
-As soon as the brake pedal starts to feel ever so slightly more harder to press, the engine should start up and restore brake vacuum.
*As soon as the brake pedal starts to feel ever so slightly more harder to press, the engine should start up and restore brake vacuum.
-If the brake pedal starts to feel much harder to press before the engine restarts, or the engine does not restart at all after servo assistance has gone, it is possible the switch is worn and is not operating at specification, or otherwise not working.
*If the brake pedal starts to feel much harder to press before the engine restarts, or the engine does not restart at all after servo assistance has gone, it is possible the switch is worn and is not operating at specification, or otherwise not working.


== Part and ordering information ==
== Part and ordering information ==


Part number: 1H0 919 825
Part number: 1H0 919 825

Revision as of 15:29, 15 December 2012

The brake booster vacuum switch (F190) informs the Digiswing control unit whether the pressure in the brake system is satisfactory.

Type: open/closed Colour: Red

Switch closed: below 0.7 bar (vacuum pressure too low). Measuring block status: "1" Switch open: above 0.7 bar (vacuum pressure OK). Measuring block status "0"

If the switch closes (vacuum pressure too low), the engine is off, and the vehicle is moving, the engine is immediately restarted to restore vacuum to the brake circuit via the mechanical exhauster.

If this switch is closed, the priority shift valve is closed and the clutch and brake circuits are separated, the engine will not switch off.

Incorrect information exists in the SSP regarding this switch. If this switch fails, engine control running lamp K111 [k111] does not illuminate, however, the engine is still prevented from switching off.

Test procedure without diagnostic equipment

  • Start engine and leave Ecomatic mode on
  • Find a downhill gradient or open stretch of road which is safe to carry out the procedure below.
  • Allow vehicle to start rolling down the gradient with engine off
  • Keep pressing brake pedal on and off.
  • As soon as the brake pedal starts to feel ever so slightly more harder to press, the engine should start up and restore brake vacuum.
  • If the brake pedal starts to feel much harder to press before the engine restarts, or the engine does not restart at all after servo assistance has gone, it is possible the switch is worn and is not operating at specification, or otherwise not working.

Part and ordering information

Part number: 1H0 919 825