New pages
Jump to navigation
Jump to search
16 December 2012
- 12:4612:46, 16 December 2012 Alternator control lamp (K2) (hist | edit) [123 bytes] Deylan (talk | contribs) (Created page with "This warning lamp is suppressed by the ECU when the engine is off to avoid it illuminating due to the engine being stopped.")
- 12:4612:46, 16 December 2012 Oil pressure control lamp (K3) (hist | edit) [123 bytes] Deylan (talk | contribs) (Created page with "This warning lamp is suppressed by the ECU when the engine is off to avoid it illuminating due to the engine being stopped.")
15 December 2012
- 21:2121:21, 15 December 2012 95Ah battery (hist | edit) [26 bytes] Deylan (talk | contribs) (Redirected page to 92Ah battery)
- 21:0621:06, 15 December 2012 Gear display control lamp (K48) (hist | edit) [227 bytes] Deylan (talk | contribs) (Created page with "The gear display control lamp is the light that illuminates on the instrument cluster to warn you about an incorrect gear selection. It will flash if you are in too high gear...")
- 21:0421:04, 15 December 2012 Ecomatic control lamp (K110) (hist | edit) [394 bytes] Deylan (talk | contribs) (Created page with "The Ecomatic control lamp (K110) is the orange lamp that illuminates on the instrument cluster to indicate that Ecomatic mode has been disabled and thus the engine will not tu...")
- 21:0021:00, 15 December 2012 Engine running control lamp (K111) (hist | edit) [480 bytes] Deylan (talk | contribs) (Created page with "The Engine running control lamp (K111) is the green lamp that illuminates on the instrument cluster to indicate that the engine will not turn itself off. It is also sometimes...")
- 17:4517:45, 15 December 2012 9Ah auxiliary battery (hist | edit) [531 bytes] Deylan (talk | contribs) (Created page with "The 9Ah auxiliary battery is used to provide power to neccesary electrical consumers when the engine is being started, to avoid power interruptions. Original battery made by ...")
- 17:4317:43, 15 December 2012 Power steering relay (J320) (hist | edit) [56 bytes] Deylan (talk | contribs) (Created page with "Relay required to operate Power Steering Pump (V119)")
- 17:4217:42, 15 December 2012 Control unit for second battery and lights (J328) (hist | edit) [593 bytes] Deylan (talk | contribs) (Created page with "The control unit for second battery and lights is required to switch the power from the main battery to the auxiliary battery during an engine starting procedure, this is so p...")
- 17:4217:42, 15 December 2012 90 ampere alternator (hist | edit) [241 bytes] Deylan (talk | contribs) (Created page with "Larger alternator than standard 1Y engine vehicle. Volkswagen felt it was neccessary that the ecomatic was fitted with a larger alternator due to the higher power consumption ...")
- 17:4117:41, 15 December 2012 Power steering pump (V119) (hist | edit) [257 bytes] Deylan (talk | contribs) (Created page with "Electronic power steering pump, replaces engine driven power steering pump used on non-ecomatic vehicles. Pump is activated if ignition is on and vehicle is moving (for examp...")
- 17:4017:40, 15 December 2012 Ecomatic instrument cluster (hist | edit) [941 bytes] Deylan (talk | contribs) (Created page with "The Ecomatic instrument cluster is similar to the standard instrument cluster fitted to Mk3 Golfs. It is the analoge clock version (no rev counter). Despite not having a rev-c...")
- 17:4017:40, 15 December 2012 92Ah battery (hist | edit) [1,252 bytes] Deylan (talk | contribs) (Created page with "Larger battery than standard vehicle, largest battery out of the whole Mk3 range. Original part number: 000 915 105 AH (95Ah 450A) (dropped) Replacement part number: 000 915 ...")
- 17:4017:40, 15 December 2012 Coolant pump (V50) (hist | edit) [2,133 bytes] Deylan (talk | contribs) (Created page with "The coolant pump V50 is electrically powered and is operated when the ignition is switched on, its function is to continue circulating water around the engine/heater matrix wh...")
- 16:5616:56, 15 December 2012 Clutch positioner vacuum valve (N183) (hist | edit) [161 bytes] Deylan (talk | contribs) (Created page with "This valve is located within the clutch final control element, and opens or closes the vacuum supply to the clutch element (i.e., pulls clutch open via suction).")
- 16:5516:55, 15 December 2012 Clutch positioner discharge valve (N184) (hist | edit) [201 bytes] Deylan (talk | contribs) (Created page with "This valve is located within the clutch control element, and opens or closes to remove vacuum (i.e., let air in) to the cluch final control element (close the clutch). This i...")
- 16:5416:54, 15 December 2012 Electric vacuum pump (V22) (hist | edit) [935 bytes] Deylan (talk | contribs) (Created page with "The vacuum pump V22 provides vacuum for the clutch system ONLY, and is operated whenever there is insufficient vacuum in the clutch system (recognized by the opening of the [[...")
- 16:5316:53, 15 December 2012 Vacuum pump relay (J318) (hist | edit) [49 bytes] Deylan (talk | contribs) (Created page with "This is the relay to operate the vacuum pump V22.")
- 16:5216:52, 15 December 2012 Vacuum reservoir (hist | edit) [236 bytes] Deylan (talk | contribs) (Created page with "The vacuum reservoir is located in the front left wheel housing underneath the battery, and has seperate compartments to store the clutch and brake vacuum -- the vacuum system...")
- 16:5216:52, 15 December 2012 Mechanical vacuum pump (hist | edit) [164 bytes] Deylan (talk | contribs) (Created page with "The mechanical vacuum pump creates vacuum from the drive of the engine. This provides vacuum for the brake system, and clutch system depending on operational state.")
- 16:5116:51, 15 December 2012 Servo motor (hist | edit) [42 bytes] Deylan (talk | contribs) (Redirected page to Clutch final control element)
- 16:5016:50, 15 December 2012 Clutch positioner (hist | edit) [42 bytes] Deylan (talk | contribs) (Redirected page to Clutch final control element)
- 16:5016:50, 15 December 2012 Clutch final control element (hist | edit) [2,143 bytes] Deylan (talk | contribs) (Created page with "This is the whole unit responsible for clutch operation (opening/closing). It has the ability to completely regulate the position of the clutch according to the demands of the...")
- 16:4816:48, 15 December 2012 Console (Bracket for clutch positioner) (hist | edit) [2,677 bytes] Deylan (talk | contribs) (Created page with "The "Console" is a metal bracket which is bolted onto the transmission, which, in turn, the Servo Motor and Vacuum Pump are attached to. Part number: 1H0 142 303 B / 1H014230...")
- 16:4516:45, 15 December 2012 Priority switch valve (N185) (hist | edit) [935 bytes] Deylan (talk | contribs) (Created page with "The priority shift valve connects the brake and clutch vacuum circuits. When the engine is running, providing the brake servo is sufficient, the valve opens and the two vacuu...")
- 16:2216:22, 15 December 2012 Diesel engine stop switch (F207) (hist | edit) [1,178 bytes] Deylan (talk | contribs) (Created page with "The diesel engine stop switch is located near the coolant reservoir, this switch informs Digiswing when the bonnet is lifted. If the vehicle is in gear, the vehicle is shu...")
- 16:2216:22, 15 December 2012 Door contact switch (F2) (hist | edit) [1,186 bytes] Deylan (talk | contribs) (Created page with "The door opening switch on the drivers door is installed to serve three purposes # When the drivers door is opened, the Digiswing control unit briefly actuates the clutch...")
- 16:1916:19, 15 December 2012 Gear operating switch (F191) (hist | edit) [1,669 bytes] Deylan (talk | contribs) (Created page with "The gear operating switch is installed in the gearshift knob and detects vertical movement along the gearstick. When Ecomatic mode is switched off, because the clutch is not ...")
- 16:1816:18, 15 December 2012 Coolant temperature sender (G62) (hist | edit) [408 bytes] Deylan (talk | contribs) (Created page with "This temperature sender reports to the Digiswing control unit the temperature of the engine coolant, this is required to stop the engine switching off when the coolant tem...")
- 16:1716:17, 15 December 2012 Gear monitor switch (F209) (hist | edit) [1,452 bytes] Deylan (talk | contribs) (Created page with "The gear monitor switch is a supplementary switch which detects whether a gear has been properly engaged, if a gear is only partially engaged this informs the Digiswing co...")
- 16:1616:16, 15 December 2012 Road speed sender (G22) (hist | edit) [311 bytes] Deylan (talk | contribs) (Created page with "The road speed sender is used to report to the Digiswing controller how fast the vehicle is moving. Its primary function is to report when the vehicle is stopped (i.e., tu...")
- 16:1416:14, 15 December 2012 Engine speed sender (G28) (hist | edit) [456 bytes] Deylan (talk | contribs) (Created page with "The engine speed sender monitors the engine speed and reports the value to the DIGISWING control unit. It is required so the DIGISWING controller can start the engine correctl...")
- 16:1316:13, 15 December 2012 Gearbox speed sender (G38) (hist | edit) [219 bytes] Deylan (talk | contribs) (Created page with "This sensor measures the speed of the gearbox input shaft and it's primary purpose is to calculate the clutch slip, to enable smooth clutch operation, and also learn clutch we...")
- 15:4915:49, 15 December 2012 Load signal potentiometer (G157) (hist | edit) [4,015 bytes] Deylan (talk | contribs) (Created page with "The load signal potentiometer is in essence a Throttle Position Sensor (TPS), it effectively informs the Digiswing control unit the position of the accelerator pedal, and ...")
- 15:3915:39, 15 December 2012 Ecomatic switch (E163) (hist | edit) [388 bytes] Deylan (talk | contribs) (Created page with "The Ecomatic switch is installed onto the window wash/wipe stalk and when pressed is used to turn the Ecomatic operation on or off. This switch is spring loaded and sends a 12...")
- 15:3615:36, 15 December 2012 Clutch travel distance sender (G162) (hist | edit) [789 bytes] Deylan (talk | contribs) (Created page with "This is a potentiometer located inside the top of the clutch final control element, it has a thin piece of string on it attached to the diaphragm of the lower part of the elem...")
- 15:3415:34, 15 December 2012 Pressure switch for clutch system F210 (hist | edit) [664 bytes] Deylan (talk | contribs) (Created page with "The clutch system pressure switch (F210) informs the DIGISWING control unit whether the clutch system pressure is satisfactory. Type: open/closed Colour: Green Switch opened...")
- 15:2815:28, 15 December 2012 Brake booster vacuum switch (F190) (hist | edit) [1,772 bytes] Deylan (talk | contribs) (Created page with "The brake booster vacuum switch (F190) informs the DIGISWING control unit whether the pressure in the brake system is satisfactory. Type: open/closed Colour: Red Switch clos...")
- 15:2515:25, 15 December 2012 Reinforced starter motor (hist | edit) [1,393 bytes] Deylan (talk | contribs) (Created page with "The Ecomatic is equipped with a stronger starter motor than the standard vehicle. It is highly recommended to fit the genuine starter motor. == Part and or...")
- 15:2515:25, 15 December 2012 Starter motor (hist | edit) [38 bytes] Deylan (talk | contribs) (Redirected page to Reinforced starter motor)
- 15:2315:23, 15 December 2012 Gear display switch (F208) (hist | edit) [2,118 bytes] Deylan (talk | contribs) (Created page with "The gear display switch (also known as the gear recognition switch) reports to the DIGISWING controller what gear is currently engaged, or the neutral gate it is in. == Outpu...")
- 15:1915:19, 15 December 2012 Ecomatic (hist | edit) [27 bytes] Deylan (talk | contribs) (Redirected page to Golf Ecomatic)
- 15:1815:18, 15 December 2012 Brake light switch (F) (hist | edit) [585 bytes] Deylan (talk | contribs) (Created page with "The brake light switch sends information to the Digiswing control unit about whether the brake pedal is pressed. As far as I know this switch is used to tell the control u...")
- 15:1415:14, 15 December 2012 Reinforced Starter Motor (hist | edit) [38 bytes] Deylan (talk | contribs) (Created page with "The Ecomatic is equipped with a stronger starter motor than the standard vehicle. The original part has now been supposedly superseded. It is highly recomme...")
- 15:1015:10, 15 December 2012 Fuel shut-off valve (N109) (hist | edit) [222 bytes] Deylan (talk | contribs) (Created page with "This is used to allow the Digiswing control unit to stop the engine when it is running. When the power flow to the fuel shut-off valve is interrupted, the fuel supply to ...")
- 15:0615:06, 15 December 2012 Starter relay (J53) (hist | edit) [404 bytes] Deylan (talk | contribs) (Created page with "This relay is supplied with power from the Digiswing controller which activates the starter motor. This is what makes a ticking noise twice when the engine restarts. When I r...")
- 01:3401:34, 15 December 2012 Tow starting (hist | edit) [1,396 bytes] Deylan (talk | contribs) (Created page with "An Ecomatic can be tow/push started. == Prerequisites == -Battery has sufficient power to operate ECU, electric vacuum pump (to create vacuum), and the clutch final control ...")
- 01:3001:30, 15 December 2012 Digiswing (hist | edit) [7,103 bytes] Deylan (talk | contribs) (Created page with "'''Digiswing/Ecomatic Control Unit J327''' Digiswing is the Ecomatic Control Unit and is an Engine and Clutch Management System. Technically it is a Powertrain Control Module...")
14 December 2012
- 17:3917:39, 14 December 2012 Golf Ecomatic (hist | edit) [11,410 bytes] Deylan (talk | contribs) (Created page with "The Volkswagen Golf Ecomatic got its name from the words "Ecology" and "Automatic", and was produced late 1993 - mid 1994 with mention in press statements as early as 1992. It...")
- 17:2617:26, 14 December 2012 Main Page (hist | edit) [2,211 bytes] MediaWiki default (talk)